
Nov
How to Read a Grow Light Spec Sheet: PPF, PPFD and µmol/J
Watts tell you what a grow light costs to run. They don’t tell you how much light it makes. To compare fixtures, you need three numbers from the spec sheet: PPF, µmol/J and a PPFD map. Here’s what each means, using our FXL-320 spec sheet as the example.
The three numbers that matter
| Term | What it measures | Unit | FXL-320 |
|---|---|---|---|
| PPF (photosynthetic photon flux) | Total usable light the fixture puts out each second | µmol/s | 850 µmol/s @ 277V |
| µmol/J (efficacy, also called PPE) | Light out per watt in. The single best measure of efficiency | µmol/J | 2.63 µmol/J @ 277V |
| PPFD (photosynthetic photon flux density) | Light landing on one spot of the canopy each second | µmol/m²/s | Depends on hang height and area |
Think of PPF as the size of the hose, µmol/J as how little water pressure it takes, and PPFD as how wet one patch of lawn gets.
Check the math. PPF ÷ watts should roughly equal the efficacy. For the FXL-320: 850 ÷ 320 = 2.66 µmol/J, in line with its rated 2.63. When a spec sheet’s numbers don’t agree with each other, ask why.
What does µmol/m²/s mean?
It’s the unit of PPFD: how many micromoles of usable light land on one square meter of canopy each second. Leafy greens do well at about 140–245 µmol/m²/s over a 16-hour day, and fruiting crops want 350–520 or more. See the crop table in our grow light rack setup guide.
Is there a PPF meter?
Not a handheld one. PPF is measured in a lab with an integrating sphere and printed on the spec sheet. A quantum (PAR) meter measures PPFD at one spot, which is how you check a fixture’s PPFD map at your own hang height.
Why a single PPFD number isn’t enough
PPFD changes across the footprint. It’s highest directly under the fixture and falls off toward the edges. A sheet that lists one big PPFD figure is almost always quoting the center.
Ask for, or look for, a PPFD map: a grid of readings across the whole footprint at a stated hang height. Then compare:
- Average PPFD across the grid, which tells you what most of your plants get.
- Corner readings, which tell you what your weakest plants get.
- Uniformity, the minimum divided by the average. Closer to 1.0 is more even.
A fixture can post an impressive center number and still leave the corners underlit.
The rest of the sheet
| Spec | What to look for | FXL-320 |
|---|---|---|
| Input voltage | Whether it runs on your circuits; efficacy is often quoted at the highest voltage | 100–277V, PF > 0.97 |
| Rated life | Hours of use the maker stands behind | 50,000 hours |
| Light source | Named LED maker and package | Lumileds 3030 |
| Spectrum chart | Shape of the light across 380–800 nm | Full-spectrum chart on sheet |
| Beam angle | How widely light spreads | 120° |
| Recommended hang height | Minimum distance above the canopy | At least 12″ |
| Dimming | How low it goes, and how | Down to 10% |
| IP rating | Protection from dust and water | IP66 |
| Certifications | Electrical safety (UL or ETL) and efficiency (DLC) | ETL, DLC |
| Warranty | Length and who backs it | 5 years |
Red flags
- “Equivalent” wattage only. “Replaces a 1000W HPS” says nothing measurable.
- Lumens or lux instead of PPF. Those measure light for human eyes, not plants.
- No PPF or µmol/J anywhere. If a fixture lists only PPFD, you can’t compare its total output or efficiency.
- Efficacy without a voltage. Many fixtures are a little less efficient at 120V than at 277V. Ask for the figure at the voltage you’ll run.
- A DLC claim the seller can’t back up. Ask for the DLC listing documentation. A reputable seller will send it.
See a full spec sheet: Edisun FXL Series · Edisun LIT Series. Questions about any number on them? Ask us.










