When to Dim Your Grow Light (and How Much). Young seedlings in a propagation tray under a softly dimmed LED grow light.
14

Nov

When to Dim Your Grow Light (and How Much)

A grow light at full power isn’t always doing your plants a favor. Seedlings, cuttings and leafy greens often need far less light than a modern LED puts out, and every extra photon costs power and heat. A dimmable light lets you give each crop and stage the light it actually uses. Here’s when to turn it down, and by how much.

Work back from the light your crop needs

The target is the daily light integral (DLI): the total light a crop gets in a day. Divide it by your photoperiod to find the intensity (PPFD) to dim to.

PPFD = DLI ÷ (hours of light × 0.0036)

Stage or cropTypical DLI targetPPFD at 16 hPPFD at 18 h
Cuttings, rooting4–1170–19060–170
Seedlings and young plants10–12175–210155–185
Lettuce and leafy greens8–14140–245125–215
Most finished ornamentals10–12 and up175–210+155–185+

Targets are from Purdue and Michigan State University extension research and a vertical-farming lettuce study (sources below). Check your crop’s own guidance and confirm with a PAR meter at canopy height.

Compare that with what a fixture puts out at full power. On a 2×4 ft shelf, an Edisun FXL-320 delivers roughly 860 µmol/m²/s, four or five times what lettuce needs. Dimming is how you use the same light for seedlings now and a higher-light crop later.

Four times to dim

1. Seedlings and cuttings. Young plants need moderate light. MSU research cites a DLI of about 10 for good young-plant quality; below that they stretch and take longer to finish, and Purdue found transplant quality rose with DLI up to about 12. Light well above that mostly adds cost. Start low and raise the light as the plants establish.

2. Leafy greens. Lettuce and most greens grow well at a DLI of 8–14. Pushing lettuce much higher tends to cause tipburn rather than faster growth.

3. Longer days. If you run an 18-hour day instead of 12, you can dim the light and still reach the same DLI. See 18/6 vs. 12/12 grow light schedules.

4. Greenhouses on bright days. When the sun provides part of the day’s light, supplemental fixtures can run lower. See greenhouse supplemental lighting.

Raise the light gradually

Plants moved from low light to high light can stress. When seedlings move to a brighter stage, or a crop goes from a dim propagation area to full production, raise the intensity over several days instead of all at once. Dimming lets you do that without moving the fixture.

Dim instead of raising the light

It’s tempting to cut intensity by hanging a light higher. That spreads light over a bigger area, but it also sends more of it past the canopy and onto walls. Dimming lowers intensity while keeping the fixture at the height where its light is most even across the canopy. Keep fixtures at or above the minimum hang height, and dim to fine-tune.

What dimming does to your power bill

An LED’s power draw drops roughly in line with its output, so a light at 50% uses about half the power and puts less heat into the room. LEDs can even be slightly more efficient at reduced drive current, as Michigan State University’s floriculture team notes, though driver efficiency at low output varies by fixture.

As a rough example: an FXL-320 dimmed to 50% for a lettuce crop draws about 160W instead of 320W. See what it costs to run a grow light to work out your own numbers.

Every Edisun light dims to 10%

SeriesBest fitDims to
LITTents and small rooms10%
FXLGreenhouse benches, racks10%
FlareVertical racks10%
BurstLarge rooms, greenhouses10%

Not sure what setting your crop needs? Send us your crop and space and we’ll suggest a fixture and a starting setting.

Sources

Leave a Reply

Your email address will not be published. Required fields are marked *

RELATED

Posts